Installation Guide
Tools Needed:
- Adjustable wrench set
- Pipe thread sealant
- Screwdrivers (flat and Phillips)
- Level
- Tape measure
Step-by-Step Installation
- Choose Installation Location: Select a clean, dry, well-ventilated location with adequate clearance for maintenance and operation.
- Prepare the Foundation: Place compressor on a solid, level concrete floor capable of supporting the unit's weight.
- Electrical Connection: Connect to a dedicated 240V, 60Hz circuit with proper grounding. Consult local electrical codes.
- Air System Setup: Install proper air filtration, regulators, and lubricators if required for your applications.
- Drain Installation: Connect drain lines to tank drain valve if automatic draining is required.
- Pressure Settings: Adjust pressure switch cut-in and cut-out settings according to application requirements.
- Initial Startup: Perform initial startup following the break-in procedure outlined in the manual.
Specifications
| Model Series | VT6276 |
| Type | Two-Stage Air Compressor |
| Color | Industrial Blue |
| Tank Capacity | 60 Gallons |
| Noise Level | 78 dB |
| Control Type | Magnetic Starter with Pressure Switch |
| Motor Power | 5 HP |
| Air Delivery | 15.8 CFM at 175 PSI |
| Max Pressure | 175 PSI |
| Power Requirements | 240V, 60Hz, 23A |
| Dimensions (HxWxD) | 65 x 30 x 30 inches |
| Weight | 420 lbs |
| Pump Type | Cast Iron Two-Stage |
Warranty Information
- Full Warranty: 2 years parts and labor
- Pump Warranty: 5 years on cast iron pump
- Tank Warranty: Lifetime limited warranty
- Additional Coverage: Optional extended warranty available
For warranty service, contact Campbell Hausfeld Customer Service at 1-800-328-4123 or visit CampbellHausfeld.com
Key Features
Two-Stage Pump System
Dual-stage compression provides higher efficiency and cooler operation, delivering more air with less energy consumption and extended pump life.
Cast Iron Construction
Heavy-duty cast iron pump and components ensure durability, better heat dissipation, and longer service life in demanding industrial environments.
Magnetic Starter
Professional-grade magnetic starter provides overload protection and allows for remote control operation, enhancing safety and convenience.
ASME Certified Tank
60-gallon ASME certified tank meets highest safety standards and includes a lifetime warranty for peace of mind in industrial applications.
Low RPM Operation
Slow-running pump (1025 RPM) reduces wear, extends component life, and operates quieter than high-speed compressors.
Industrial Duty Components
Features industrial-grade pressure switch, check valve, safety valve, and gauges for reliable performance in continuous duty applications.
Application Capabilities
Spray Painting
Consistent pressure for professional finish spraying applications
Sandblasting
Adequate CFM for medium-duty abrasive blasting operations
Air Tools
Powers multiple impact wrenches, ratchets, and grinders simultaneously
Tire Service
High volume for tire inflation and mounting equipment
Pneumatic Systems
Supports automated machinery and production line equipment
Construction
Runs nail guns, staplers, and other construction tools efficiently
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Compressor won't start | Power issue, pressure switch fault, thermal overload | Check power supply, reset overload protector, inspect pressure switch |
| Low pressure output | Air leaks, worn rings, intake filter clogged | Check for leaks, inspect pump rings, clean/replace air filter |
| Excessive noise/vibration | Loose components, worn bearings, improper mounting | Tighten all fasteners, check bearings, ensure proper installation |
| Overheating | Dirty cooling fins, low oil, restricted ventilation | Clean cooling surfaces, check oil level, improve ventilation |
| Oil in air lines | Worn piston rings, overfilled oil, wrong oil type | Check rings, drain excess oil, use proper compressor oil |
| Frequent cycling | Air leaks, faulty check valve, worn unloader | Locate and repair leaks, replace check valve, service unloader |
Maintenance Codes & Indicators
- Red Pressure Gauge: Operating pressure - Monitor during use
- Yellow Pressure Gauge: Tank pressure - Check when compressor is off
- Oil Sight Glass: Oil level indicator - Maintain between min/max marks
- Thermal Overload Reset: Red button on motor - Press if motor overheats
- Pressure Switch Light: Indicates when compressor is running
- Safety Valve: Automatic release at 200 PSI - Test monthly
Manual Downloads
Current Model Manuals
VT6276
60 Gallon Two-Stage Compressor
VT6275
60 Gallon Single-Stage Compressor
VT6278
60 Gallon Industrial Compressor
VT6280
60 Gallon Vertical Compressor
Popular Previous Models
VT6165
60 Gallon Professional Compressor
VT6199
60 Gallon Shop Compressor
VT6144
60 Gallon Commercial Compressor
VT6111
60 Gallon Standard Compressor