Installation Guide
Tools Needed:
- Adjustable wrench set
- Level
- Screwdrivers (flat and Phillips)
- Pipe wrench
- Tape measure
- Safety glasses and gloves
Step-by-Step Installation
- Choose Installation Location: Select a well-ventilated area with solid, level concrete flooring and adequate clearance for maintenance.
- Uncrating and Inspection: Remove all shipping materials and inspect for damage. Check oil level in pump before operation.
- Electrical Connection: Connect to dedicated 230V, 60Hz circuit with proper grounding. Requires 30-40 amp circuit breaker.
- Air System Setup: Install proper air filtration, regulator, and lubricator if required for your tools. Use Teflon tape on all threaded connections.
- Drain Installation: Connect drain line to tank drain valve and route to appropriate drainage location.
- Leveling: Adjust leveling feet to ensure compressor is perfectly level to prevent vibration and uneven wear.
- Initial Startup: Open tank drain valve, turn power on, and allow compressor to build pressure. Check for leaks during first cycle.
Specifications
| Model Series | CMXGXAN060V7 |
| Type | Stationary Vertical Air Compressor |
| Horsepower | 7 HP |
| Tank Capacity | 60 Gallons |
| Max Pressure | 175 PSI |
| CFM at 90 PSI | 18.1 CFM |
| CFM at 40 PSI | 22.1 CFM |
| Pump Type | Two-Stage Cast Iron |
| Motor Type | 7 HP, 230V, Single Phase |
| Dimensions (HxWxD) | 72 x 30 x 30 inches |
| Weight | 325 lbs |
| Noise Level | 85 dB |
Warranty Information
- Full Warranty: 2 years parts and labor
- Pump Warranty: 5 years limited warranty
- Tank Warranty: Lifetime limited warranty
- Additional Coverage: Extended service plans available
For warranty service, contact Craftsman Customer Service at 1-888-331-4569 or visit Craftsman.com
Key Features
Two-Stage Pump System
Dual piston design provides higher pressure and greater efficiency. First stage compresses air to intermediate pressure, second stage delivers full 175 PSI output.
ASME Certified Tank
60-gallon ASME certified tank with lifetime warranty. Features industrial-grade construction with safety valve and pressure gauge.
Industrial Duty Motor
7 HP, 230V single-phase motor with thermal overload protection and heavy-duty start capacitor for reliable operation under continuous use.
Automatic Tank Drain
Electronic auto-drain system removes moisture automatically, preventing corrosion and maintaining air quality for tools.
Low Oil Shutdown
Protection system automatically shuts down compressor when oil level is too low, preventing pump damage and costly repairs.
Vibration Isolation
Rubber isolation mounts reduce vibration and noise transmission, protecting the compressor and building structure.
Performance Specifications
Air Tools
Supports multiple tools simultaneously: impacts, sanders, grinders
Spray Painting
Consistent pressure for professional finish spraying applications
Sandblasting
Adequate CFM for small to medium sandblasting cabinets
Tire Service
Rapid inflation for truck and automotive tires
Pneumatic Nailers
Continuous operation for framing and finish nail guns
Shop Air
General shop air for cleaning, inflation, and pneumatic systems
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Compressor won't start | Power issue, pressure switch fault, thermal overload | Check power supply, reset thermal overload, test pressure switch |
| Low pressure output | Leaking valves, worn rings, intake filter clogged | Check for leaks, inspect valves and rings, clean/replace air filter |
| Excessive noise/vibration | Loose components, worn bearings, improper mounting | Tighten all fasteners, check bearings, ensure proper leveling |
| Overheating | Dirty cooling fins, low oil, restricted airflow | Clean cooling fins, check oil level, ensure adequate ventilation |
| Frequent cycling | Air leaks, faulty check valve, worn pump | Check for system leaks, test check valve, inspect pump |
| Oil in air lines | Worn piston rings, overfilled oil, faulty separator | Check oil level, inspect rings, replace separator element |
Maintenance Codes & Indicators
- Red Light Flashing: Thermal overload - Allow cool down, check ventilation
- Yellow Light On: Maintenance required - Check oil, filter, and drain
- Green Light Off: Power issue - Check circuit breaker and connections
- Pressure Gauge Fluctuation: Valve issue - Inspect intake/exhaust valves
- Unusual Knocking: Bearing wear - Inspect connecting rods and bearings
- Slow Recovery: Pump wear - Check piston rings and cylinder
Manual Downloads
Current Model Manuals
CMXGXAN060V7
60 Gallon 7HP Vertical
CMXGXAN080V7
80 Gallon 7HP Vertical
CMXGXAN060V5
60 Gallon 5HP Vertical
CMXGXAN060V7H
60 Gallon 7HP Horizontal
Popular Previous Models
919.167380
60 Gallon 5HP Professional
919.167381
60 Gallon 6.5HP Industrial
CMEC6150
60 Gallon 5HP Cast Iron
CMXFXAN060V5
60 Gallon 5HP Two-Stage