Installation Guide
Tools Needed:
- Adjustable wrench set
- Pipe thread sealant
- Screwdrivers (flat and Phillips)
- Level
- Teflon tape
Step-by-Step Installation
- Choose Installation Location: Select a clean, dry, well-ventilated area with sufficient clearance for maintenance and operation.
- Position the Compressor: Place on a solid, level surface capable of supporting the weight (approximately 150 lbs when empty).
- Check Oil Level: Verify oil level is at the center of the sight glass before first use.
- Electrical Connection: Connect to a properly grounded 120V, 15A dedicated circuit. Use appropriate gauge extension cord if needed.
- Air System Setup: Install air filter on intake, connect air hose to regulated outlet using appropriate fittings.
- Pressure Settings: Adjust pressure switch cut-in and cut-out settings according to tool requirements.
- Initial Test Run: Run compressor without load for 30 minutes to break in pump, then check for leaks under pressure.
Specifications
| Model Series | CMEC6150 |
| Type | Vertical Tank Air Compressor |
| Tank Capacity | 30 Gallons |
| Motor Type | 1.6 HP, 120V Induction Motor |
| Pump Type | Oil-Lubricated Twin Cylinder |
| Maximum Pressure | 175 PSI |
| CFM at 40 PSI | 7.1 CFM |
| CFM at 90 PSI | 5.7 CFM |
| Noise Level | 78 dB |
| Dimensions (HxWxD) | 50 x 20 x 20 inches |
| Weight (Empty) | 150 lbs |
| Duty Cycle | 50% at 90 PSI |
Warranty Information
- Full Warranty: 2 years parts and labor
- Tank Warranty: Lifetime limited warranty against defects
- Pump Warranty: 3 years on pump assembly
For warranty service, contact Craftsman Customer Service at 1-888-331-4569 or visit Craftsman.com
Key Features
ASME Certified Tank
30-gallon ASME certified tank provides ample air storage for continuous operation of multiple tools with enhanced safety standards.
Oil-Lubricated Pump
Twin-cylinder oil-lubricated pump delivers longer life, quieter operation, and better performance than oil-free models.
Thermal Overload Protection
Built-in thermal overload protection prevents motor damage from overheating during extended use or high ambient temperatures.
Dual Voltage Capability
Convertible motor allows operation on either 120V or 240V power supply for optimal performance in different workshop setups.
Integrated Pressure Gauge
Large, easy-to-read pressure gauge with color-coded zones indicates tank pressure and regulated output pressure simultaneously.
Quick-Connect Coupler
Industrial-style quick-connect air coupler accepts all standard 1/4" NPT fittings for fast tool changes without tools.
Recommended Applications
Air Tools
Ideal for impact wrenches, ratchets, drills, and sanders up to 5.5 CFM requirement
Spray Painting
Sufficient capacity for HVLP spray guns and automotive painting applications
Inflating
Perfect for tires, sports equipment, inflatable pools, and air mattresses
Cleaning
Powerful airflow for workshop cleaning, dust removal, and drying applications
Nailing/Fastening
Continuous operation for framing nailers, finish nailers, and staplers
Air Brushing
Precise pressure control suitable for detailed airbrush artwork
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Compressor won't start | Power issue, pressure switch fault, thermal overload tripped | Check power supply, reset thermal overload, check pressure switch settings |
| Low pressure output | Leaks in system, worn piston rings, clogged air filter | Check for leaks with soap solution, replace piston rings if needed, clean air filter |
| Excessive noise/vibration | Loose mounting bolts, worn motor bearings, piston slap | Tighten all bolts, check motor bearings, inspect piston and cylinder |
| Oil in air lines | Overfilled oil, worn piston rings, faulty air/oil separator | Drain to proper level, replace piston rings, check separator |
| Frequent cycling | Air leaks, faulty check valve, worn pressure switch | Locate and repair leaks, replace check valve, adjust pressure switch |
| Motor overheats | Low voltage, restricted ventilation, excessive duty cycle | Check voltage supply, ensure proper clearance, observe duty cycle limits |
Maintenance Schedule
- Daily: Drain moisture from tank, check oil level
- Weekly: Inspect hoses and connections for leaks
- Monthly: Clean air filter, check belt tension (if applicable)
- Every 3 Months: Change compressor oil (or per hours of use)
- Annually: Replace air filter, inspect safety valve
- Every 2 Years: Replace pressure switch if showing wear
Manual Downloads
Current Model Manuals
CMEC6150
30-Gallon Vertical Air Compressor
CMEC6250
60-Gallon Two Stage Compressor
CMXCEC362
6-Gallon Pancake Compressor
CMEC6130
20-Gallon Horizontal Compressor
Popular Previous Models
919.152412
33-Gallon Vertical Compressor
919.167380
27-Gallon Hot Dog Compressor
919.152411
15-Gallon Portable Compressor
919.165620
4-Gallon Hot Dog Compressor