Installation Guide
Tools Needed:
- Adjustable wrench
- Level
- Screwdrivers (flat and Phillips)
- Pliers
- Tape measure
- Air hose fittings
Step-by-Step Installation
- Choose Installation Location: Select a clean, dry, well-ventilated location with adequate clearance for air flow and maintenance access.
- Check Oil Level: Before first use, check the oil level in the pump and add recommended compressor oil if necessary.
- Position the Compressor: Place on a solid, level surface to minimize vibration during operation.
- Electrical Connection: Connect to a properly grounded 120V, 15A, AC outlet with correct circuit protection. Do not use an extension cord.
- Air System Setup: Install air filter on intake, connect air hose to outlet using appropriate fittings, and ensure all connections are tight.
- Pressure Settings: Adjust pressure regulator to desired output pressure (not exceeding tool requirements).
- Initial Test Run: Run compressor without load for 10-15 minutes to break in, then check for leaks and proper pressure buildup.
Specifications
| Model Series | HUSKY-175PSI-PRO |
| Type | Single Stage, Oil-Lubricated |
| Color | Black/Orange |
| Maximum Pressure | 175 PSI |
| Noise Level | 78 dB |
| Tank Capacity | 30 Gallons |
| Motor Type | 1.8 HP, 120V Induction Motor |
| CFM at 90 PSI | 5.8 CFM |
| CFM at 40 PSI | 7.2 CFM |
| Power Requirements | 120V, 60Hz, 15A |
| Dimensions (HxWxD) | 50 x 24 x 30 inches |
| Weight | 180 lbs |
| Pump Speed | 1725 RPM |
Warranty Information
- Full Warranty: 2 years parts and labor
- Pump Warranty: 5 years on compressor pump
- Tank Warranty: Lifetime limited warranty on ASME tank
- Additional Coverage: Optional extended warranty available
For warranty service, contact Husky Customer Service at 1-800-431-1700 or visit HuskyTools.com
Key Features
High-Efficiency Pump
Cast iron construction with large bore cylinders provides maximum air delivery with minimal heat buildup and extended pump life.
ASME Certified Tank
30-gallon ASME certified tank with corrosion-resistant interior coating ensures safety and durability for long-term use.
Thermal Overload Protection
Built-in thermal overload protection automatically shuts off motor if it overheats, preventing damage and ensuring safety.
Dual Pressure Gauges
Separate gauges for tank pressure and regulated output pressure allow for precise control of air tools.
Low Oil Shutoff
Automatic shutoff system protects pump from damage when oil level falls below minimum requirement.
Quick-Connect Coupler
Industrial-style quick-connect air coupler allows for fast tool changes without tools or shutoff.
Recommended Applications
Air Tools
Ideal for impact wrenches, ratchets, drills, and sanders up to 5.8 CFM requirement
Spray Painting
Consistent pressure delivery for HVLP spray guns and paint applications
Inflating
Quick inflation of vehicle tires, sports equipment, and inflatables
Nailing/Stapling
Power for framing nailers, finish nailers, and staplers
Cleaning
High-pressure air for cleaning tools, equipment, and work areas
Air Brushing
Precise pressure control for detailed airbrush work
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Compressor won't start | Power issue, pressure switch fault, thermal overload tripped | Check power supply, reset thermal overload, check pressure switch |
| Low pressure output | Air leak, worn piston rings, clogged air filter | Check for leaks, inspect piston rings, clean or replace air filter |
| Excessive noise/vibration | Loose components, worn bearings, uneven surface | Tighten all fasteners, check bearings, ensure level installation |
| Overheating | Dirty cooling fins, low oil, restricted ventilation | Clean cooling fins, check oil level, improve ventilation |
| Oil in air lines | Overfilled oil, worn piston rings, wrong oil type | Drain excess oil, inspect rings, use recommended compressor oil |
| Frequent cycling | Air leak, faulty pressure switch, undersized tank | Check for leaks, adjust pressure switch, verify application requirements |
Maintenance Schedule
- Daily: Check oil level, drain moisture from tank, inspect for leaks
- Weekly: Clean air filter, check belt tension (if applicable), inspect hoses
- Monthly: Check all fasteners, inspect safety valve, clean cooling fins
- Every 3 Months: Change compressor oil, inspect piston and valves
- Annually: Replace air filter, check motor brushes, professional inspection
- Every 2 Years: Replace safety valve, complete system overhaul
Manual Downloads
Current Model Manuals
HUSKY-175PSI-PRO
30-Gallon 175 PSI Air Compressor
HUSKY-150PSI-STD
30-Gallon 150 PSI Air Compressor
HUSKY-175PSI-VERT
30-Gallon Vertical 175 PSI Compressor
HUSKY-200PSI-PRO
30-Gallon 200 PSI Industrial Compressor
Popular Previous Models
HUSKY-165PSI-20G
20-Gallon 165 PSI Air Compressor
HUSKY-155PSI-PORT
Portable 155 PSI Air Compressor
HUSKY-175PSI-60G
60-Gallon 175 PSI Two-Stage Compressor
HUSKY-135PSI-PANCAKE
6-Gallon Pancake Air Compressor