Installation Guide
Tools Needed:
- Adjustable wrench set
- Pipe wrench
- Screwdrivers (flat and Phillips)
- Teflon tape
- Level
- Air hose fittings
Step-by-Step Installation
- Choose Installation Location: Select a clean, dry, well-ventilated area with sufficient clearance for maintenance and operation.
- Prepare the Foundation: Place compressor on a solid, level concrete floor capable of supporting 300+ pounds.
- Electrical Connection: Connect to a dedicated 240V, 60Hz, 15A circuit with proper grounding. Consult local electrical codes.
- Air System Setup: Install air filter on intake, connect air lines using Teflon tape on all threaded connections.
- Drain Installation: Connect drain line to tank drain valve and route to appropriate drainage location.
- Pressure Settings: Set pressure switch cut-in at 100 PSI and cut-out at 135 PSI for optimal performance.
- Initial Startup: Fill with compressor oil to proper level, open tank drain briefly, then start compressor for initial break-in.
Specifications
| Model Number | C602H |
| Type | Vertical Air Compressor |
| Tank Capacity | 60 Gallons |
| Horsepower | 5 HP |
| Maximum Pressure | 175 PSI |
| CFM at 90 PSI | 14.5 CFM |
| CFM at 40 PSI | 16.5 CFM |
| Motor Type | 230V Single Phase |
| Pump Type | Two-Stage Cast Iron |
| Noise Level | 78 dB |
| Dimensions (HxWxD) | 65 x 24 x 30 inches |
| Weight | 285 lbs |
| Oil Type | ISO 100 Compressor Oil |
Warranty Information
- Full Warranty: 2 years parts and labor
- Tank Warranty: Lifetime limited warranty
- Pump Warranty: 3 years on cast iron pump
For warranty service, contact Husky Customer Service at 1-800-431-1700 or visit HuskyTools.com
Key Features
Two-Stage Pump
Industrial-grade cast iron two-stage pump provides higher efficiency, longer life, and better cooling than single-stage compressors.
ASME Certified Tank
60-gallon ASME certified tank with lifetime warranty provides reliable air storage for continuous operation of multiple tools.
Magnetic Starter
Built-in magnetic starter with overload protection prevents motor damage from low voltage or excessive current draw.
Low Oil Shutdown
Automatic shutdown system protects pump from damage when oil level falls below minimum safe operating level.
Thermal Overload Protection
Motor includes automatic thermal overload protection to prevent overheating during extended operation.
Industrial Pressure Switch
Heavy-duty pressure switch with manual reset provides reliable pressure control and system protection.
Performance Specifications
Air Tools
Supports 2-3 air tools simultaneously including impacts, ratchets, and sanders
Spray Painting
Provides consistent pressure for HVLP and conventional spray guns
Sandblasting
Adequate CFM for small to medium sandblasting cabinets
Tire Inflation
Quick inflation of truck, tractor, and automotive tires
Air Nailers
Powers multiple framing and finishing nailers continuously
Cleaning
Sufficient air for blow guns and cleaning applications
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Compressor won't start | Power issue, pressure switch fault, thermal overload tripped | Check power supply, reset pressure switch, allow motor to cool |
| Low pressure output | Leaking fittings, worn pump rings, clogged air filter | Check for leaks with soap solution, inspect pump, clean/replace filter |
| Excessive noise/vibration | Loose mounting bolts, worn motor bearings, unbalanced pulley | Tighten all bolts, check bearings, inspect pulley alignment |
| Oil in air lines | Overfilled oil, worn piston rings, faulty separator | Check oil level, inspect pump, replace separator element |
| Frequent cycling | Air leaks, faulty check valve, worn pressure switch | Locate and repair leaks, replace check valve, adjust pressure switch |
| Motor overheating | Low voltage, restricted ventilation, dirty cooling fins | Check voltage, ensure proper clearance, clean motor fins |
Maintenance Codes & Indicators
- Red Oil Light: Low oil level - Shut down immediately and add oil
- Yellow Service Light: Regular maintenance due - Check filter and oil
- Continuous Running: Air leak detected - Check system for leaks
- Failure to Build Pressure: Pump issue - Check valves and rings
- Excessive Moisture: Drain issue - Check automatic drain function
- Pressure Fluctuation: Regulator problem - Inspect pressure regulator
Manual Downloads
Current Model Manuals
C602H
60-Gallon Vertical Compressor
C502H
50-Gallon Vertical Compressor
C802H
80-Gallon Vertical Compressor
C602V
60-Gallon Vertical Quiet Series
Popular Previous Models
C601H
60-Gallon Single Stage
C452H
45-Gallon Vertical Compressor
C302H
30-Gallon Portable Compressor
C262H
26-Gallon Pancake Compressor