Installation Guide
Tools Needed:
- Adjustable wrench set
- Screwdrivers (flat and Phillips)
- Pipe thread sealant
- Air pressure gauge
- Level
Step-by-Step Installation
- Choose Installation Location: Select a clean, dry, well-ventilated area with adequate clearance for maintenance and operation.
- Unpack and Inspect: Remove all packaging materials and inspect for shipping damage. Ensure all components are present.
- Position the Compressor: Place on a solid, level surface. Use vibration pads if installing on concrete floor.
- Electrical Connection: Connect to appropriate power supply (120V or 240V as specified). Ensure proper grounding.
- Air System Setup: Install air filter, connect air hoses using appropriate fittings. Apply thread sealant to all connections.
- Oil Check: Check oil level (if oil-lubricated model). Fill to proper level with recommended compressor oil.
- Initial Test Run: Run compressor without load for 10 minutes to break in. Check for leaks and proper pressure buildup.
Specifications
| Model Series | XP Series / VT Series |
| Type | Stationary Air Compressor |
| Horsepower | 3.5 HP - 6.5 HP |
| Tank Capacity | 20 Gallon - 60 Gallon |
| Max Pressure | 125 PSI - 175 PSI |
| CFM at 90 PSI | 4.0 CFM - 15.5 CFM |
| Voltage Requirements | 120V / 240V Single Phase |
| Motor Type | Induction Motor, Oil-Lubricated |
| Pump Type | Cast Iron, Two-Stage |
| Noise Level | 75 dB - 85 dB |
| Dimensions (LxWxH) | Varies by model |
| Weight | 150 lbs - 300 lbs |
Warranty Information
- Full Warranty: 1 year parts and labor
- Pump Warranty: 2 years on cast iron pump
- Tank Warranty: Lifetime limited warranty
- Additional Coverage: Extended warranty available
For warranty service, contact Campbell Hausfeld Customer Service at 1-800-328-8523 or visit CampbellHausfeld.com
Key Features
ASME Certified Tank
Heavy-duty ASME certified air tank with rust-resistant coating for maximum durability and safety compliance.
Cast Iron Pump
Durable cast iron construction provides superior heat dissipation and extended pump life with minimal maintenance.
Thermal Overload Protection
Built-in thermal overload protection automatically shuts off motor to prevent damage from overheating.
Low Oil Shut-off
Automatic shut-off system protects pump when oil level falls below minimum requirement.
Pressure Control System
Precise pressure switch with automatic start/stop function maintains consistent air pressure.
Easy Drain Valve
Quick-release drain valve allows for easy moisture removal from tank to prevent corrosion.
Application Guide
Air Tools
Ideal for impact wrenches, ratchets, and air drills requiring 4-6 CFM
Spray Painting
Provides consistent pressure for HVLP spray guns and paint applications
Framing Nailers
Sufficient capacity for continuous operation of framing and finish nailers
Inflation
Perfect for tires, sports equipment, and inflatable products
Cleaning
Powerful airflow for workshop cleaning and dust removal
Sandblasting
Higher CFM models suitable for light to medium sandblasting tasks
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Compressor won't start | Power issue, pressure switch, thermal overload | Check power supply, reset overload, check pressure switch setting |
| Low pressure output | Air leaks, worn valves, intake filter clogged | Check for leaks, inspect valves, clean or replace air filter |
| Excessive noise/vibration | Loose components, worn bearings, improper mounting | Tighten all fasteners, check bearings, ensure proper installation |
| Overheating | Dirty cooling fins, low oil, excessive cycling | Clean cooling fins, check oil level, allow proper cool-down time |
| Oil in air lines | Overfilled oil, worn piston rings | Drain excess oil, inspect and replace piston rings if necessary |
| Frequent cycling | Air leaks, faulty check valve | Check for leaks, inspect and replace check valve if needed |
Maintenance Codes & Schedule
- Daily: Drain moisture from tank, check oil level
- Weekly: Inspect hoses and connections, check for leaks
- Monthly: Clean air filter, check belt tension (if applicable)
- Quarterly: Change oil (oil-lubricated models), inspect valves
- Annually: Complete system inspection, safety valve test
- Biannually: Replace air filter element
Manual Downloads
Current Model Manuals
XP2060V
6.5 HP 60-Gallon Vertical
VT6275
5 HP 27-Gallon Twin Stack
XP2204V
4 HP 20-Gallon Vertical
VT6360
6 HP 60-Gallon Two-Stage
Popular Previous Models
FP2094
4 HP 30-Gallon Single Stage
VT6185
5 HP 18-Gallon Portable
WL611000
6 HP 11-Gallon Wheelbarrow
HS5160
1.6 HP 6-Gallon Hot Dog