Installation Guide
Tools Needed:
- Adjustable wrench set
- Pipe thread sealant (Teflon tape)
- Air hose (3/8" recommended)
- Pressure regulator
- Safety glasses and gloves
Step-by-Step Installation
- Choose Installation Location: Select a clean, dry, well-ventilated area with solid, level flooring and adequate clearance for maintenance.
- Unpack and Inspect: Remove all packaging materials and inspect for shipping damage. Check oil level in pump.
- Position the Compressor: Place on a level surface. Use vibration pads if installing on concrete floor.
- Electrical Connection: Connect to a dedicated 120V, 15A grounded outlet. Ensure proper circuit breaker protection.
- Air System Setup: Install air filter on intake, connect air hose to outlet using thread sealant, and install pressure regulator if not pre-installed.
- Drain Installation: Connect drain hose to tank drain valve and route to appropriate drainage location.
- Initial Test Run: Open tank drain valve, turn on compressor, allow to build pressure, then shut off and check for leaks.
Specifications
| Model Series | TS-20G-V2 |
| Type | Vertical Tank Air Compressor |
| Tank Capacity | 20 Gallons |
| Motor Type | 1.5 HP, 120V, Single Phase |
| Max Pressure | 125 PSI |
| CFM at 90 PSI | 5.1 CFM |
| CFM at 40 PSI | 6.2 CFM |
| Pump Type | Oil-Lubricated, Single Stage |
| Noise Level | 78 dB |
| Dimensions (HxWxD) | 50 x 20 x 20 inches |
| Weight | 125 lbs |
| Outlet Size | 1/4" NPT |
Warranty Information
- Full Warranty: 2 years parts and labor
- Tank Warranty: Lifetime limited warranty
- Motor Warranty: 3 years on compressor motor
- Additional Coverage: Optional extended warranty available
For warranty service, contact Tool Shop Customer Service at 1-800-555-COMPRESS or visit ToolShop.com
Key Features
ASME Certified Tank
20-gallon ASME certified tank provides ample air storage for continuous tool operation with enhanced safety and durability standards.
Thermal Overload Protection
Built-in thermal overload protection automatically shuts off motor if it overheats, preventing damage and extending motor life.
Low Oil Shut-off
Automatic shut-off system activates when oil level is too low, protecting the pump from damage due to insufficient lubrication.
Dual Voltage Capability
Convertible motor allows operation on either 120V or 240V power supply for flexibility in different workshop setups.
Quick-Connect Coupler
Industrial-style quick-connect air coupler allows fast tool changes without tools or thread sealant.
Pressure Regulator with Gauge
Precise pressure regulator with easy-read gauges allows accurate pressure adjustment for different tools and applications.
Recommended Applications
Air Tools
Ideal for impact wrenches, ratchets, drills, and sanders
Spray Painting
Sufficient CFM for HVLP spray guns and paint sprayers
Tire Inflation
Fast inflation for car, truck, and motorcycle tires
Nail Guns
Perfect for framing, finishing, and roofing nailers
Cleaning
Powerful air flow for workshop cleaning and dust removal
Air Brushing
Precise pressure control for detailed airbrush work
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Compressor won't start | Power issue, pressure switch fault, thermal overload | Check power supply, reset thermal overload, check pressure switch |
| Low pressure output | Air leaks, worn piston rings, faulty pressure regulator | Check for leaks, inspect piston rings, test pressure regulator |
| Excessive noise/vibration | Loose components, worn bearings, improper mounting | Tighten all fasteners, check bearings, ensure proper installation |
| Overheating | Dirty cooling fins, low oil, restricted ventilation | Clean cooling fins, check oil level, improve ventilation |
| Oil in air lines | Overfilled oil, worn piston rings, faulty air/oil separator | Check oil level, replace piston rings, inspect separator |
| Slow recovery time | Air leaks, worn valves, undersized power supply | Check for leaks, inspect valves, verify adequate power |
Maintenance Schedule
- Daily: Drain moisture from tank, check oil level
- Weekly: Check for air leaks, clean intake filter
- Monthly: Inspect belts and pulleys, check safety valve
- Every 3 Months: Change compressor oil, clean cooling fins
- Annually: Replace air filter, inspect check valve
- Every 2 Years: Replace safety valve, rebuild kit if needed
Manual Downloads
Current Model Manuals
TS-20G-V2
20 Gallon Vertical Compressor
TS-20G-H2
20 Gallon Horizontal Compressor
TS-30G-V2
30 Gallon Vertical Compressor
TS-20G-PRO
20 Gallon Professional Series
Popular Previous Models
TS-20G-V1
20 Gallon First Generation
TS-15G-V2
15 Gallon Vertical Compressor
TS-25G-H1
25 Gallon Horizontal Compressor
TS-20G-OILFREE
20 Gallon Oil-Free Compressor